N7 COSPLAY BUILD – GAUNTLETS

Mass Effect N7 Armour build – Gauntlets

I have finally done it. I have finally finished…one piece of my armour. Raise your hands and shout hallelujah!
I didn’t screw it up…well that’s a lie, I screwed up a little, but still, I actually managed to make something, look like the something it’s supposed to look like. Whoop Whoop!

‘Clears throat. Composes self’

Right…

Celebrations out of the way, I want to show the gauntlets I made for my N7 armour. Which, in my opinion, were the easiest thing to make and paint. Below are some pictures of the gauntlets all shiny and new, painted with red and white acrylic paint.

Unfortunately in my haste to finish my gauntlets, I neglected to take pictures before I painted them, but just imagine them grey and…foamy.

ArmsThe process of painting is a long laborious one, but it pays off in the end as the foam looks shiny and holds a metallic tint, without you spending money on a metallizer.

Firstly, cover the foam in two coats of PVA and water, waiting for them to completely dry before painting over them. Add a thin sheen of Plasti-dip and wait another four hours for the foam to completely dry.

Next, spray paint the entire piece with a silver spray paint, (I just use fast dry project enamel.)

Lastly, spray paint over the silver, whatever colour you want your armour to be, the silver undercoating leaves a metallic shine under the second layer and even aids to adding battle damage such as scuffs and weathering.

Here are my finished gauntlets with battle damage. To make the cracks, simply cut the foam with a crafting knife then heat the area

Arms damagedwith a heat gun, the foam will expand from the head and open up, leaving a gash in the foam. Simply paint the inside of the cracks silver, rub in the paint with your finger and leave to dry.

If you wish to create scuffs, get a bit of masking tape, stick it on to the place you want to create a scuff and rip it off. The masking tape will rip away the second layer slightly, leaving specks of silver underneath.

This is only one way of creating scuffs and battle marks.

Advertisements

N7 ARMOUR BUILD – Torso

N7 ARMOUR BUILD – Torso

If you are a first time Cosplay builder and you want something difficult, finicky and rage inducing to build, look no further than the N7 armour the protagonist wears in Mass Effect. Many experienced Cosplay builders will probably laugh at the fact I am finding this armour build so hard, but it has generally been pretty difficult.

I must first start by saying that I have not been using templates. I have been looking at other Cosplay builds and basing my designs off of them, as well as the design in the game.

BackFor those of you who do not know what the N7 armour actually looks like, the picture on the left will give you a pretty good idea.

For those of you who are aware of what it looks like, please excuse the blond Shepard, and that god-awful purple uniform, she is not mine… (Going slightly off topic for a second burn blond Shepard with fire.)

Right….moving on.

I am aware that in all my excitement to show the world my build, silently hoping that it won’t end up looking like a space marine in a blender, I have neglected to list the tools I am using to create my armour.  You can find a full list of these tools at the bottom of this article.

You may find the picture on the right here pretty familiar, I posted it a few weeks ago to show how I created the breast plate. What torso frontyou see here is the detail burnt into the foam using a cheap soldering iron.

Quick tip: When burning in the pattern across the breasts, be sure to place the breastplate over the template you used to mould them, that way, the breasts will not deform when heated with the soldering iron, unless you want deformed boobs like mine.

For the detailing, a soldering iron works pretty well, but if you have a little extra money for a wood burning kit, I would suggest you get that, the extra tips come in handy for later detailing.

The part I found most difficult about the torso, was the back. There are a lot of extra small parts that you need to cut out and stick on separately. That can become pretty difficult when your hands shake like a squirrel on meth.

Back 1You can see my attempt in the picture on the left. As you can see, I need to redo the silver…things (I have no idea what they are called) as they are a bit wonky, and the shield generator also needs to be redone, but all in all, I am pretty happy with how the back turned out.

Quick tip: To make to the folds of the box on the back, the soldering iron comes in very hands. Just get a ruler, draw a line where you want the fold to be, burn it into the foam and voilà!

After I have formed the rest of the armour I shall be painting it. However, I am having some trouble in that department, even when using the Plastidip.

Any help would be greatly appreciated.

List of tools needed

Heat gun – Used for heating and forming the foam. Can also be used to seal the foam when ready to be painted.
Soldering Iron / Wood burning kit – Used for detailing and creating folds.
– Crafting knife – For cutting the foam.
– Plastidip – For sealing the foam before painting.
Glue gun – For glueing..
-Work Gloves – To keep you hands clean and safe from the material.
– Mask – So you don’t breath in an smoke when heating the foam