Category: Gaming

N7 COSPLAY BUILD – GAUNTLETS

Mass Effect N7 Armour build – Gauntlets

I have finally done it. I have finally finished…one piece of my armour. Raise your hands and shout hallelujah!
I didn’t screw it up…well that’s a lie, I screwed up a little, but still, I actually managed to make something, look like the something it’s supposed to look like. Whoop Whoop!

‘Clears throat. Composes self’

Right…

Celebrations out of the way, I want to show the gauntlets I made for my N7 armour. Which, in my opinion, were the easiest thing to make and paint. Below are some pictures of the gauntlets all shiny and new, painted with red and white acrylic paint.

Unfortunately in my haste to finish my gauntlets, I neglected to take pictures before I painted them, but just imagine them grey and…foamy.

ArmsThe process of painting is a long laborious one, but it pays off in the end as the foam looks shiny and holds a metallic tint, without you spending money on a metallizer.

Firstly, cover the foam in two coats of PVA and water, waiting for them to completely dry before painting over them. Add a thin sheen of Plasti-dip and wait another four hours for the foam to completely dry.

Next, spray paint the entire piece with a silver spray paint, (I just use fast dry project enamel.)

Lastly, spray paint over the silver, whatever colour you want your armour to be, the silver undercoating leaves a metallic shine under the second layer and even aids to adding battle damage such as scuffs and weathering.

Here are my finished gauntlets with battle damage. To make the cracks, simply cut the foam with a crafting knife then heat the area

Arms damagedwith a heat gun, the foam will expand from the head and open up, leaving a gash in the foam. Simply paint the inside of the cracks silver, rub in the paint with your finger and leave to dry.

If you wish to create scuffs, get a bit of masking tape, stick it on to the place you want to create a scuff and rip it off. The masking tape will rip away the second layer slightly, leaving specks of silver underneath.

This is only one way of creating scuffs and battle marks.

N7 BUILD – Greaves

Building the Greaves – First try (Still need to be painted) 

Boots2

I spent most of the day yesterday building the greaves for my N7 armour and I have to say, I am pretty happy with how it turned out. The picture on the left is the unpainted base for the N7 greaves, made with a Nike shoe spray painted black, and a shin pad.

I did not use any templates for the foam, so I was expecting the greaves to be a disaster, but I am pretty happy with them. The next stage is to paint them red and add battle damage. Boots 1

The engraved lines were created by cutting the foam with a very sharp knife, then heating the foam so it expands.

This is what they look like when I put them on. As you can see they still need to be painted and the laces need to be changed. When it comes to finishing them, I shall be painting them red and black. Attempting to add battle damage and weathering.

Wish me luck!

N7 Armour build update!

Building the weapon

Having to put the armour build on hold until I get paid, I have decided to build a weapon to go with my armour. I did not have enough foam to build a weapon, so I decided I would create my own shotgun with a Mass Effect look and feel using a water-gun!

I started out thinking it was going to be a disaster, but it actually turned out looking pretty good. (I think)

I used the M-300 Claymore as a template for my own weapon build, then tried to find a water-gun that looked similar in shape to the weapon shown below.

This is the M-300 CLAYMORE
This is the M-300 CLAYMORE

I then painted the water gun with black, silver, red and white, creating my own spin on the M300 Claymore, painting the distinctive N7 stripe down the side.

Below are pictures of the gun before it was painted and after it was painted. Hope you like it!

Water gun before

After

Day 2 – N7 Armour build!

Sorry for the massive delay, I have been super busy!

Anyway, the armour build is going well, much better then I expected. You can see the progress below, along with some descriptions and pointers of how to make your own. As I said in my previous post, I am using EVA foam for this armour build.So far, I have not had any problems with it. It’s easy to cut, east to shape and holds a good, sturdy shape when the foam cools.

Chest
Chest

What you see here is the chest piece. I know it looks a little wonky, but when it’s wrapped around my torso, it looks pretty good, I must say that I am pretty proud of it. The bottom piece is just a template for the lower torso. As you can see, I have not added the detail yet.

To make the chest piece, I used a thick bit of wood and two circular sauce dishes. (See below.) I glued the dishes to the plank of wood. (Which was originally a door to…something ) and put paper-mache over the top to make the flat bottoms of the the dishes more rounded.

Sauce dishes for boobs!
Sauce dishes for boobs!

I then took my flat chest template, and heated it under the grill until it was soft enough to mould.

WARNING: Wear gloves and a face mask, the smoke  the EVA foam gives off is toxic. Make sure you ventilate your workspace. Do not let the foam burn.

After the EVA foam is soft, it will become floppy. Mould the foam to the breast template as quickly as possible, making sure to press down hard on the bits you wish to mould. Weight the foam down, or have a friend help you. If you don’t do it the first time, repeat the process, but flatten out the foam first before giving it a second try.

This took me six tries.

Chest piece on its own
Chest piece on its own